Asterisk::First Steps After Installation

Dikopi dari sini http://www.freepbx.org/book/export/html/14170 supaya gampang carinya

First Steps After Installation

UPDATE: These instructions are a bit dated, for the most recent update please visit our new wiki which will show you how to Install FreePBX, First Steps After Installation, and how to keep it updated. Follow this link: http://wiki.freepbx.org/display/HTGS/How+to+Get+Started+Home

IMPORTANT NOTE: These instructions were written with FreePBX 2.9 in mind. FreePBX 2.10 has been released since these instructions were written, and involves a major overhaul of the user interface. The modules were grouped together on the left hand side of the screen in 2.9. In 2.10, they are accessed from a series of pull-down menus at the top of the screen. What is written below should work just fine with 2.10 once you are able to locate the appropriate module on the pull-down menus.

———–

After you finish installing FreePBX, the FreePBX Distro, or another Distro that includes FreePBX, there are a few things you want to do first:

Important note Part 2: The installation steps must be completed with the Chrome browser. If not using Chrome you will not see the initial configuration dialog box.
Read more »

Mera: cek status

Cara baca summary aktifitas mera secara global dengan cara dibawah ini ;

[belajar@mera bin]# ./mp_shell.x sh st
Mera VoIP Transit Softswitch ( 1000 Advanced  SORM )
Release 3.1.2 build 3102-0039 (Dec 15 2006 06:06:58) HASP

---------------------- Common statistics ----------------------
 Host : 192.168.1.1
  Start time        : 30/01/2013 15:03:39
  Up time           : 0 days 21 hours 46 minutes
  Stat start time   : 30/01/2013 15:03:39
  Stat duration     : 0 days 21 hours 46 minutes
  Max load          : 153 calls
  Calls duration    : 44116 minute(s)
  Active calls      : 37
  Active AVG 1m (5m): 44.11 (47.54)
  Call rate 1m (5m) : 0.49 (0.45) (unlimited)
  Call rate maximum : 2.38 at 30/01/2013 15:37:24
  Full CR   1m (5m) : 0.49 (0.45)
  Full CR   maximum : 2.38 at 30/01/2013 15:37:24
  Received calls    : 31160
  Normal   calls    : 26977
  Failed   calls    : 4146
  Rejected calls    : 0
  Received Kb       : 12810715
  Written  Kb       : 12811846

Read more »

Cisco: Upgrade vcware dan dspware modul dsp AS5300

Berawal dari tidak sesuainya firmware modul DSP dengan IOS yang terpasang :(
hikz

GAMBIR1#sh vfc 1 version vcware

Voice Feature Card in Slot 1:
     VCWare Version     :  11.32
     ROM Monitor Version:  1.3
     DSPWare Version    :  4.1.32
     Technology         :  C549
Firmware version mismatch for bundle AS5300 VCWare
  - version found (11.32) is lower than minimum required (11.41)
Firmware version mismatch for bundle AS5300 C549
  - version found (4.1.32) is lower than minimum required (4.1.41)

GAMBIR1#sh vfc 2 version vcware

Voice Feature Card in Slot 2:
     VCWare Version     :  11.31
     ROM Monitor Version:  1.3
     DSPWare Version    :  4.1.31
     Technology         :  C549
Firmware version mismatch for bundle AS5300 VCWare
  - version found (11.31) is lower than minimum required (11.41)
Firmware version mismatch for bundle AS5300 C549
  - version found (4.1.31) is lower than minimum required (4.1.41)

Pada contoh dibawah, akan di berikan tutorial untuk meng-upgrade firmware DSP di modul nomer 2.
Read more »

Voip:debug digium

# dahdi_hardware
pci:0000:04:00.0     wct4xxp+     d161:0410 Wildcard TE410P (4th Gen)
pri set debug on span 2
TEI=0 Got SABME from network peer.
TEI=0 Sending UA
TEI=0 Sending SABME
TEI=0 Sending SABME
TEI=0 Got SABME from network peer.
TEI=0 Sending UA
TEI=0 Sending SABME
TEI=0 Got SABME from network peer.
TEI=0 Sending UA
TEI=0 MDL-ERROR (G): T200 expired N200 times sending SABME in state 5(Awaiting establishment)
Changing from state 5(Awaiting establishment) to 4(TEI assigned)
q931.c:7700 q931_dl_indication: link is DOWN

Apanya ya ? sebelumnya pakai 420 dengan konfig yang sama normal.
hardware error atau distro error ?
belum dapat clue

Voip:Integrasi dengan E1 Telkom

Setelah driver dahdi sudah terinstall dan sudah dapat mengenali hardware digium.

Tinggal mengkonfigure chanel di dahdi dengan tools dari dahdi_genconf setelah itu restart agar konfig dikenali system.

# dahdi_genconf
# /etc/init.d/dahdi restart

Hasilnya dapat di cek dari dahdi_tools.
Pastikan alarm untuk port yang terkonek ke E1 Telkom tertulis OK.
Read more »

Voip:persiapan kompile dahdi

yum groupinstall 'Development Tools'
yum install newt-devel
yum install ncurses-devel
yum install openssl-devel